linuxmce_ap
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| linuxmce_ap [2016/01/23 20:47] – [Guest Network] admin | linuxmce_ap [2016/07/22 20:24] (current) – admin | ||
|---|---|---|---|
| Line 4: | Line 4: | ||
| sudo apt-get install bridge-utils hostapd | sudo apt-get install bridge-utils hostapd | ||
| - | ===== Run hostap ===== | ||
| - | |||
| - | sudo hostapd / | ||
| - | |||
| - | |||
| - | |||
| - | ===== Change firewall ===== | ||
| - | |||
| - | pluto main -> firewall -> IntIF -> eth0 to br0 | ||
| ===== Configs ===== | ===== Configs ===== | ||
| Line 45: | Line 36: | ||
| iface br0 inet static | iface br0 inet static | ||
| + | | ||
| + | | ||
| | | ||
| | | ||
| Line 178: | Line 171: | ||
| ssid=test | ssid=test | ||
| hw_mode=g | hw_mode=g | ||
| - | channel=1 | + | channel=7 |
| + | ieee80211n=1 | ||
| + | wmm_enabled=1 | ||
| + | ht_capab=[SHORT-GI-40] | ||
| macaddr_acl=0 | macaddr_acl=0 | ||
| auth_algs=1 | auth_algs=1 | ||
| Line 189: | Line 185: | ||
| </ | </ | ||
| - | ====== Guest Network ====== | + | |
| + | ==== / | ||
| + | |||
| + | <code config hostapd> | ||
| + | # Defaults for hostapd initscript | ||
| + | # | ||
| + | # See / | ||
| + | # methods of managing hostapd. | ||
| + | # | ||
| + | # Uncomment and set DAEMON_CONF to the absolute path of a hostapd configuration | ||
| + | # file and hostapd will be started during system boot. An example configuration | ||
| + | # file can be found at / | ||
| + | # | ||
| + | # | ||
| + | DAEMON_CONF="/ | ||
| + | |||
| + | # Additional daemon options to be appended to hostapd command:- | ||
| + | # -d show more debug messages (-dd for even more) | ||
| + | # -K | ||
| + | # -t | ||
| + | # | ||
| + | # Note that -B (daemon mode) and -P (pidfile) options are automatically | ||
| + | # configured by the init.d script and must not be added to DAEMON_OPTS. | ||
| + | # | ||
| + | # | ||
| + | </ | ||
| + | |||
| + | ===== Change firewall ===== | ||
| + | |||
| + | pluto main -> firewall -> IntIF -> eth0 to br0 | ||
| + | |||
| + | ===== Run hostap ===== | ||
| + | |||
| + | sudo hostapd / | ||
| + | |||
| + | ====== Guest Network | ||
| old mac address: | old mac address: | ||
| Line 195: | Line 226: | ||
| 10: | 10: | ||
| | | ||
| - | change it to 02: | + | change it to **02**: |
| ifconfig wlan0 down | ifconfig wlan0 down | ||
linuxmce_ap.1453582025.txt.gz · Last modified: by admin